ECD

 

 
 
 
 
 
 
 
 
 
 
ECD - Electronic Controls Design, Inc. Products
 
 
 
ECD MEGA M.O.L.E
 
 

The MEGAM.O.L.E.® 20 Profiler offers a full 20 channels, the most of any traveling profiler in the Thermal Process industry. At only 7.2 mm thick, MEGAM.O.L.E.® 20 provides a thinner and more advanced configuration than previously available, and has the capacity for over 25 separate runs before downloading data.

 
 
 
 
 
 
 
ECD Super M.O.L.E. Gold 2
 
 

Smartest Profiler on the Planet

SuperM.O.L.E.® Gold 2 continues the legacy of the original SuperM.O.L.E® Gold Thermal Profiler. With all the power of a MEGAM.O.L.E.® 20, it retains the same form factor, thermocouple connector type, channel count (6), and RIDER-product compatibility & much more.

 
 
 
 
 
 
 
ECD V-M.O.L.E
 
 

The V-M.O.L.E.® Profiler is a 3 channel profiler with the power of the MEGAM.O.L.E.® 20 profiler in a high value yet cost-effective package. The V-M.O.L.E.® Profiler provides a valuable platform for doing both Process Engineering & Process Verification. Lower operating cost… and it’s GREEN!. V-M.O.L.E.® is RoHS compatible.

 
 
 
 
 
 
 
ECD OvenRIDER Kit
 
 

The patented OvenRIDER® is the only system that will capture all critical information on oven performance. Using the SuperM.O.L.E.® Gold as it’s “heart”, the OvenRIDER® travels through your oven collecting air temperature, heat flow and conveyor speed data. A combination of thermal and placement sensors measure oven performance.

 
 
 
 
 
 
 
ECD WaveRIDER Kit
 
 

The wave soldering process is one of the most challenging procedures to set up. The ECD WaveRIDER® greatly simplifies wave solder set up and ensures perfect repeatability, time after time. Board recipe preheat temperatures, conveyor speeds, wave heights, contact times and parallelism are all measured and monitored.

 
 
 
 
 
 
 
ECD AutoM.O.L.E.Xpert Kit
 
 

When utilizing the AutoM.O.L.E.®Xpert3 System, you are entering a new phase in the thermal management of your automated soldering operations. The new AutoM.O.L.E.®Xpert3 System automatically guides you through the entire process: planning of the target profile, set-up of reflow machine parameters and verification.

 
 
 
 
 
 
 
ECD OvenWATCH
 
 

The OvenWATCH® system is designed to continuously monitor the quality of PCB assemblies as they pass through your reflow ovens. Now the OvenWATCH® system can provide you and your customers with the confidence of knowing that the quality of your PCB assemblies is being monitored 24 hours per day…..365 days per year.

 
 
 
 
 
 
 
ECD FLUXOMETER
 
 

Improve Process Quality. Take control of your spray flux process with the ECD Fluxometer®, the first easy-to-use process monitor available. The Fluxometer® is so convenient & accurate, operator can perform diagnostic checks in minutes. Designed for accuracy & ease of use, the Fluxometer™ provides you with the data to optimize.

 
 
 
 
 
 
 
ECD TEMPROBE
 
 

TEMPROBE™ is a patented, precision temperature sensing instrument. The subminiature T/C tip can be placed anywhere on a board, including profiling in wet solder paste or on fine pitch component legs.TEMPROBE™ is used in place of a conventional thermocouple to monitor the temperature of critical solder joints & components.

 
 
 
 
Temperature profiler Riders and accessories
 
 
 
ECD Side Rider
 
 

Side Rider™, an expandable safety platform designed to carry a M.O.L.E.® or another manufacturers Profiler securely through beltless reflow ovens.

 
 
 
 
 
 
 
ECD E-Z RIDER
 
 

E-Z Rider is designed to carry your profiler safely through wave solder machines. E-Z Rider's titanium side rails are gripped by the finger conveyors.

 
 
 
 
 
 
 
ECD ReflowRIDER
 
 

Reflow Rider is designed for the new reflow ovens with edge rail conveyors and no conveyor belt. Reflow Rider's side rails adjust independently.

 
 
 
«« « 1|2» »» 
 
 
For any inquiry, please contact us